|
<< 点击显示目录 >> 主页 振动监测 > X20(c)CM4810使用手册 > 寄存器说明 - Register description > 频带 - Frequency bands > 频带的配置 - FrequencyBandConfig |
Name:
FrequencyBand01Config to FrequencyBand32Config
名称:
FrequencyBand01Config to FrequencyBand32Config
General configuration of individual frequency bands.
Each frequency band can be calculated on any channel with any of the 4 speed data points (ActSpeed).
各个频段的基本配置。
每个频段都可以用 4 个速度数据点 (ActSpeed) 中的任何一个在任何通道上进行计算。
Data type 数据类型 |
Values 值 |
Bus controller default setting 总线控制器的默认设置 |
|---|---|---|
UINT |
See the bit structure. 请参阅位结构。 |
0 |
Bit 位 |
Description 描述 |
Value 值 |
Information 说明 |
|---|---|---|---|
0 - 3 |
Input channel for calculating the frequency band 用于计算频带的输入通道 |
0 |
Channel 1 (bus controller default setting) 通道 1 (总线控制器的默认设置) |
1 |
Channel 2 通道 2 |
||
2 |
Channel 3 通道 3 |
||
3 |
Channel 4 通道 4 |
||
4 to 15 |
Invalid 无效 |
||
4 - 5 |
Signal for calculating the frequency band 用于计算频带的信号 |
0 |
Raw signal speed 1) (bus controller default setting) 速度原始信号 1) (总线控制器的默认设置) |
1 |
Enveloped velocity signal 1) 速度包络信号 1) |
||
2 |
Raw acceleration signal 加速度原始信号 |
||
3 |
Enveloped acceleration signal 加速度包络信号 |
||
6 |
Speed-dependant calculation of the frequency band of the configured ActSpeed data point 对配置 ActSpeed 的数据点的频带进行与速度相关的计算 |
0 |
Off Uses FrequencyBandLowerFrequency and FrequencyBandUpperFrequency for the calculation (bus controller default setting) 关闭 使用 FrequencyBandLowerFrequency （频带频率下限）和 FrequencyBandUpperFrequency （频带频率上限）进行计算 (总线控制器的默认设置) |
1 |
On FrequencyBandDmgFreq60rpm and FrequencyBandTolerance are used for the calculation. 开启 使用 FrequencyBandDmgFreq60rpm（60 RPM 的标准损坏频率） 和 FrequencyBandTolerance（容差） 进行计算 |
||
7 |
Harmonic frequencies also calculated 计算谐波频率 |
0 |
Off (bus controller default setting) 关闭 (总线控制器的默认设置) |
1 |
On All harmonic frequencies up to the maximum frequency are always calculated. 开启 始终计算直至最大频率的所有谐波频率。 The harmonic frequencies can also include frequency portions that are the result of damage at other positions. This can lead to a misinterpretation of the measurement. 谐波频率还可能包括作为其它故障结果的频率部分，这可能会导致对测量结果的歧义。 |
||
8 - 11 |
ActSpeed data point used for the calculation if the frequency band is speed-dependent 用于计算频段是否与速度相关的 ActSpeed 数据点 |
0 |
ActSpeed01 (bus controller default setting) ActSpeed01 (总线控制器的默认设置) |
1 |
ActSpeed02 |
||
2 |
ActSpeed03 |
||
3 |
ActSpeed04 |
||
4 to 15 |
Invalid 无效 |
||
12 |
Enables noise calculation instead of RMS
启用噪声（noise）计算替代有效值
|
0 |
Off (bus controller default setting) Off (总线控制器的默认设置) |
1 |
On The speed-dependent and harmonic settings are ignored. 开启 速度相关和谐波的设置将被忽略。 |
||
13 - 14 |
Selects the quadrant to calculate the noise 选择要计算的噪声（noise）象限 |
0 |
1st quadrant from MinFrequency to 1/4 MaxFrequency 2) (bus controller default setting) 第 1 象限，从最小频率到 1/4最大频率 2) (总线控制器的默认设置) |
1 |
2nd quadrant from 1/4 MaxFrequency to 1/2 MaxFrequency 2) 第 2 象限，从 1/4最大频率 到 1/2最大频率 2) |
||
2 |
3rd quadrant from 1/2 MaxFrequency to 3/4 MaxFrequency 2) 第 3 象限，从 1/2最大频率 到 3/4最大频率 2) |
||
3 |
4th quadrant from 3/4 MaxFrequency to MaxFrequency 2) 第 4 象限，从 3/4最大频率 到 最大频率 2) |
||
15 |
Reserved 保留 |
0 |
|
1) |
This is only calculated if the EnableVelocityCalculation bit (configuration in register SensorConfig) is set for the respective channel; otherwise, 0 is output. 仅当为相应通道设置了启用速度计算（EnableVelocityCalculation）位（寄存器 SensorConfig中的配置) 时，才计算此值；否则，输出0。 |
2) |
Refers to the respective signal (raw signal or envelope signal) on the channel 指通道上的相应信号（原始信号或包络信号） |